在线超碰av,天天操天天摸天天射,免费的爱爱视频,情侣av在线,一级片中文字幕,2022国产毛片大全,精品亚洲大全

AS-BDAU-104
檢測到系統錯誤：用戶數據的長度規格太大參數\u Siglached Bit 16 E 7129 0檢測到系統錯誤：電機編碼器參數\u Warnlached Bit 16 E 712C 0檢測到系統錯誤：無法與編碼器通信參數\u Warnlached Bit 16 E 712D 4未找到電子電機銘牌參數\u Siglached Bit 16不正確的電機數據（不正確的CRC）。無電機電子銘牌的電機（如SER電機）聯系技術支持或更換電機。E 712F 0未檢測到電子電機銘牌的數據段E 7132 0系統錯誤：無法寫入電機配置E 7133 0無法寫入電機配置E 7134 4不完整的電機配置參數\u Siglached Bit 16 E 7135 4格式不受支持參數\u Siglached Bit 16 E 7136 4使用參數MotEnctype參數選擇的編碼器類型不正確\u Siglached在電機配置參數的內部轉換過程中檢測到位16 E 7137 4錯誤\u SIGLATCH位16 E 7138 4電機配置參數超出允許范圍參數\u SIGLATCH位16 E 7139 0編碼器偏移：編碼器中的數據段不正確。E 713A 3第三方電機編碼器的調整值尚未確定。參數\u Siglached Bit 16 E 7200 4檢測到系統錯誤：制造期間校準模擬/數字轉換器/不正確的BLE文件參數\u Siglached Bit 30 E 7320 4檢測到系統錯誤：編碼器參數無效\u Siglached Bit 16到編碼器的通信信道（Hiperface）受到干擾，電機編碼器尚未出廠參數化。聯系技術支持。E 7321 3從編碼器參數讀取位置超時\u SIGLACKED Bit 16通信信道（Hiperface）到編碼器受到干擾或電機編碼器不工作。檢查編碼器電纜的接線和屏蔽連接或更換電機。E 7327在Hiperface應答參數中設置了0個錯誤位\u WarnLatched bit 16 EMC不足。驗證接線（屏蔽）。

System error detected: Length specification for user data too great Parameter _SigLatched Bit 16 E 7129 0 System error detected: Motor encoder Parameter _WarnLatched Bit 16 E 712C 0 System error detected: Communication with encoder not possible Parameter _WarnLatched Bit 16 E 712D 4 Electronic motor nameplate not found Parameter _SigLatched Bit 16 Incorrect motor data (incorrect CRC). Motor without electronic motor nameplate (for example, SER motor) Contact Technical Support or replace the motor. E 712F 0 No data segment of the electronic motor nameplate E 7132 0 System error detected: Motor configuration cannot be written E 7133 0 Not possible to write motor configuration E 7134 4 Incomplete motor configuration Parameter _SigLatched Bit 16 E 7135 4 Format is not supported Parameter _SigLatched Bit 16 E 7136 4 Incorrect encoder type selected with parameter MotEnctype Parameter _SigLatched Bit 16 E 7137 4 Error detected during the internal conversion of the motor configuration Parameter _SigLatched Bit 16 E 7138 4 Parameter of the motor configuration out of permissible range Parameter _SigLatched Bit 16 E 7139 0 Encoder offset: Data segment in encoder is incorrect. E 713A 3 Adjustment value of the encoder of the third party motor has not yet been determined. Parameter _SigLatched Bit 16 E 7200 4 System error detected: Calibration analog/digital converter during manufacturing / incorrect BLE file Parameter _SigLatched Bit 30 E 7320 4 System error detected: Invalid encoder parameter Parameter _SigLatched Bit 16 Communication channel (Hiperface) to encoder is subject to interference, motor encoder has not been factoryparameterized. Contact Technical Support. E 7321 3 Timeout reading the absolute position from the encoder Parameter _SigLatched Bit 16 Communication channel (Hiperface) to encoder is subject to interference or motor encoder is inoperative. Verify wiring and shield connection of encoder cable or replace motor. E 7327 0 Error bit set in Hiperface answer Parameter _WarnLatched Bit 16 Insufficient EMC. Verify wiring (shield).