在线超碰av,天天操天天摸天天射,免费的爱爱视频,情侣av在线,一级片中文字幕,2022国产毛片大全,精品亚洲大全

AS-S911-801
eSM模塊：輸入狀態信道A和信道B不相同參數\u SigLatched Bit 23斷線或連接的設備不可用。驗證接線和連接的設備。E 782A 2 eSM模塊：輸出狀態信道A和信道B不相同參數\u SigLatched Bit 23對24V DC短路。檢測到系統錯誤。驗證接線和連接的設備。驗證STO\u A和STO\u B的連接。聯系技術支持。E 782B 3 eSM模塊：檢測到系統錯誤：檢測到位置評估錯誤（值不相同）參數\u SIGLACKED Bit 23 CPU\u A和CPU\u B的位置值不同。這種情況可能是由編碼器引起的。E 782C 3 eSM模塊：檢測到系統錯誤：檢測到速度評估錯誤（值不相同）參數\u SIGLACKED Bit 23 CPU\u A和CPU\u B具有不同的速度值。這種情況可能是由編碼器引起的。E 782F 2 eSM模塊：檢測到系統錯誤：在STO信號參數動態化過程中檢測到錯誤\u SIGLACKED Bit 23 E 7833 0 eSM模塊：檢測到系統錯誤：EEPROM校驗和不正確（加載的默認值）參數\u WARNLOCKED Bit 23 EEPROM不工作。E 7834 0 eSM模塊：安全模塊已更換（加載默認值）參數\u WarnLatched Bit 23此安全模塊未配置此驅動器。參數已重置為默認值。重新配置安全模塊。E 7835 4 eSM模塊：換向位置參數\u SIGLACKED Bit 23編碼器錯誤或檢測到的驅動器內部通信錯誤（例如，EMC）。驗證EMC。驗證編碼器連接。聯系技術支持。E 7836 4 eSM模塊：參數校驗和不一致參數\u SigLatched Bit 23 CPU\u A的參數與CPU\u B的參數不一致。無法將參數加載到安全模塊eSM中。重試將參數加載到安全模塊eSM中。如果問題仍然存在，請聯系技術支持。E 7837 0 eSM模塊：檢測到系統錯誤：引導程序：地址參數無效\u WarnLatched Bit 23引導加載程序?qū)﹂W存范圍的寫入訪問無效。E 7838 1 eSM模塊：在機器工作模式自動模式參數中超過安全限制速度（SLS）\u SigLatched Bit 23驅動速度大于配置的eSM速度限制。降低驅動器速度或驗證機器運行模式自動模式的eSM速度限制。E 7839 2 eSM模塊：輸入ESMSTART low而不是high（自動啟動）參數\u SigLatched Bit 23 ESMSTART配置為自動啟動，啟動時必須為high。驗證ESMSTART的參數配置。驗證ESMSTART的接線。E 783A 2 eSM模塊：輸入ESMSTART high而不是low（手動啟動）參數\u SigLatched Bit 23 ESMSTART配置為手動啟動，啟動時必須為low。驗證ESMSTART的參數配置。驗證ESMSTART的接線。E 783B 2 eSM模塊：防護門確認：確認信號可用時間過長。參數\u SIGLACKED Bit 23確認信號可用時間超過6秒。確認信號的可用時間必須少于6秒。

eSM module: Input states channel A and channel B are not identical Parameter _SigLatched Bit 23 Wire break or connected devices are inoperable. Verify wiring and connected devices. E 782A 2 eSM module: Output states channel A and channel B are not identical Parameter _SigLatched Bit 23 Short circuit to 24V DC. System error detected. Verify wiring and connected devices. Verify connection of STO_A and STO_B. Contact Technical Support. E 782B 3 eSM module: System error detected: Position evaluation error detected (values not identical) Parameter _SigLatched Bit 23 CPU_A and CPU_B have different position values. This condition may have been caused by the encoder. E 782C 3 eSM module: System error detected: Velocity evaluation error detected (values not identical) Parameter _SigLatched Bit 23 CPU_A and CPU_B have different velocity values. This condition may have been caused by the encoder. E 782F 2 eSM module: System error detected: Error detected during dynamization of STO signal Parameter _SigLatched Bit 23 E 7833 0 eSM module: System error detected: EEPROM incorrect checksum (default values loaded) Parameter _WarnLatched Bit 23 EEPROM inoperative. E 7834 0 eSM module: Safety module replaced (default values loaded) Parameter _WarnLatched Bit 23 This safety module has not been configured with this drive. The parameters have been reset to the default values. Reconfigure the safety module. E 7835 4 eSM module: Commutation position Parameter _SigLatched Bit 23 Encoder error or error in internal communication with the drive detected (for example, EMC). Verify EMC. Verify encoder connection. Contact Technical Support. E 7836 4 eSM module: Parameter checksums not identical Parameter _SigLatched Bit 23 Parameter of CPU_A is not identical to parameter of CPU_B. Not possible to load parameters into safety module eSM. Retry loading the parameters into the safety module eSM. If the condition persists, contact Technical Support. E 7837 0 eSM module: System error detected: Boot program: Invalid address Parameter _WarnLatched Bit 23 Invalid write access of bootloader to flash memory range. E 7838 1 eSM module: Safely Limited Speed (SLS) exceeded in machine operating mode Automatic Mode Parameter _SigLatched Bit 23 Drive velocity greater than configured eSM speed limit. Reduce velocity of the drive or verify eSM speed limit for machine operating mode Automatic Mode. E 7839 2 eSM module: Input ESMSTART low instead of high (automatic start) Parameter _SigLatched Bit 23 ESMSTART is configured for automatic start and must be high at start. Verify parameter configuration of ESMSTART. Verify wiring of ESMSTART. E 783A 2 eSM module: Input ESMSTART high instead of low (manual start) Parameter _SigLatched Bit 23 ESMSTART is configured for manual start and must be low at start. Verify parameter configuration of ESMSTART. Verify wiring of ESMSTART. E 783B 2 eSM module: Guard door acknowledgment: The acknowledgement signal is available for too long a time. Parameter _SigLatched Bit 23 The acknowledgement signal is available for more than 6 seconds. The acknowledgement signal must be available for less than 6 seconds.