在线超碰av,天天操天天摸天天射,免费的爱爱视频,情侣av在线,一级片中文字幕,2022国产毛片大全,精品亚洲大全

VXI-PCI8015
尺寸（單位：mm）VT-VSPA1K-1 VT-VSPA1-1項目規劃/維護說明/附加信息? 在調試放大器之前，必須確保根據相關應用設置印刷電路板上的DIL開關。? 在所提供的條件下，參數設置如下（有關參數設置，請參閱8頁至10頁）：大斜坡時間=5 s，導頻電流=100 mA，大輸出電流=800 mA，時鐘頻率=200 Hz。? 放大器卡只能在斷電時組裝。? 電磁閥連接不得使用帶有續流二極管或LED顯示屏的接頭。? 只能使用Ri>100 kΩ的儀器在卡上進行測量。? 與0 V工作電壓相比，測量零點（M0）增加+9 V，且未隔離，即–9 V調節電壓? 0 V工作電壓。因此，不要將測量零點（M0）連接到0 V工作電壓。? 對于切換命令值，必須使用鍍金觸點的繼電器（低電壓、低電流）。? 始終屏蔽命令值行，將屏蔽連接到卡側的接地，另一側打開。卡必須通過端子6或8接地。如果不存在系統接地，連接0 V工作電壓。? 建議：還要屏蔽電磁閥導體。對于長度不超過50 m的電磁閥導線，使用線型LiYCY 1.5 mm2。如需更長的長度，請聯系我們。? 與架空線路、無線電和雷達系統的距離必須至少為1米。? 不要將電磁閥導線和信號線放在電源線附近。? 卡上平滑電容器的充電功率要求預保險絲具有緩慢熔斷的特性。? 注意：如果使用不同的輸入，則必須始終同時連接或斷開兩個輸入。

Dimensions (dimensions in mm) VT-VSPA1K-1 VT-VSPA1-1 Project planning/maintenance instructions/additional information ? It has to be ensured before commissioning of the amplifi ers that the DIL switches on the printed circuit board are set according to the relevant application. ? In the condition as supplied the parameters are set as follows (for the parameter setting refer to pages 8 to 10): Max. ramp time = 5 s, pilot current = 100 mA, max. output current = 800 mA, clock frequency = 200 Hz. ? The amplifi er card may only be assembled when de-energized. ? No connectors with free-wheeling diodes or LED displays must be used for solenoid connection. ? Only carry out measurements at the card using instruments Ri > 100 kΩ. ? Measurement zero (M0) is increased by +9 V compared to 0 V operating voltage and not isolated, i.e. –9 V regulated voltage ? 0 V operating voltage. Thus, do not connect measurement zero (M0) to 0 V operating voltage. ? For switching command values, relays with gold-plated contacts have to be used (low voltages, low currents). ? Always shield command value lines, connect shielding to earth on the card-side, other side open. The card has to be connected to the earth via terminal 6 or 8. If no system earth exists, connect 0 V operating voltage. ? Recommendation: Also shield the solenoid conductor. For solenoid conductors up to 50 m in length, use the line type LiYCY 1.5 mm2. For greater lengths, please contact us. ? The distance to aerial lines, radios, and radar systems has to be 1 m at least. ? Do not lay solenoid conductors and signal lines near power lines. ? The charging power of the smoothing capacitor on the card requires the pre-fuses to be of a slow-blowing nature. ? Notice: If the diff erential input is used, both inputs must always be connected or disconnected at the same time.